|
|
|
|
|
|
|
|
|
|
|
Teledyne Laars R0021300 Transformer, 40VA, 115/24V Kit, Rheos and Rheos+, 1200, 1600, 2000, 2400
|
LAARS R0061400 Pressure Relief Valve, 30 PSI
|
LAARS RE2000300 Fuse Holder Kit (5 pack)
|
|
|
|
|
|
|
|
|
|
|
|
|
LAARS 20150902 Heat Exchanger Baffle 400
|
LAARS R20150200 Machined Bronze Inlet/Outlet Header Cover for Std. Heat Exchanger
|
LAARS R20150100 Machined Bronze Rear Header Cover
|
|
|
|
|
|
|
|
|
|
|
|
|
LAARS RS2003000 Gasket Replacement Kit
|
LAARS Q0068400 Pilot Gas Tubing (per ft.)
|
Teledyne Laars RE0240900 Pressure Switch S.P./D.T.
|
|
|
|
|
|
|
|
|
|
|
|
|
LAARS A2088100 Blower, Left hand, Lo Nox Mighty Therm
|
Teledyne Laars Burner Plenum Gasket Kit, 400
|
TELEDYNE LAARS R2006600 Sensor, Temperature, Johnson Control, (previous part #E2103700), Rheos and Rheos+, 1200, 1600, 2000, 2400
|
|
|
|
|
|
|
|
|
|
|
|
|
TELEDYNE LAARS R2007700 On/Off Switch
|
LAARS P0076100 Compression Nut & Sleeve for Q0068400 Pilot 1/4" Gas Tubing
|
Teledyne Laars F0011400 Header Bolt Washer
|
|
|
|
|
|
|
|
|
|
|
|
|
Honeywell L4008E1271 High Limit, Manual Reset, PNCH
|
LAARS S2003100 Heat Exchanger Gasket (Front)
|
Teledyne Laars R2023000 3-Try Ignition Control (Natural Gas) previous part #s E2101300, E2321600, E2105100
|
|
|
|
|
|
|
|
|
|
|
|
|
Teledyne Laars RE2101600 Digital Temperature Display
|
LAARS RW2002300 Hot Surface Ignitor w/Gasket
|
LAARS RE2101400 Electronic Temperature Control
|
|
|
|
|
|
|
|
|
|
|
|
|
Teledyne Laars E2103100 Sensor Probe
|
Teledyne Laars E2103700 HTS Temperature Sensor, R2006600
|
LAARS RV2003900 Operating Gas Valve Kit 320-400
|
|
|
|
|
|
|
|
|
|
|
|
|
Teledyne Laars W0038001 Ignitor & Gasket kit, Mighty Therm LoNox
|
LAARS 20259602 Complete 4-Pass Heat Exchanger w/Copper Tubes 400
|
LAARS R20256102 Tube Assembly w/Copper Tubes 400
|
|
|
|
|
|
|
|
|
|
|
|
|
Teledyne Laars RE0015900 High Limit Kit, E0015900
|
Laars 10-332 Ignitor Gasket, CB/HWG
The igniter is a “glow bar” type silicon carbide unit. It is energized whenever there is a call for heat and the red "IGNITER" light on the boiler control is lit. After the igniter is switched off and the boiler continues to run, the igniter functions as a flame sensor for the boiler control. If the ignitor fails and must be replaced, always install a new igniter gasket with the replacement igniter. CAUTION: Ignitor gets hot.
|
Teledyne Laars RE0013000 Flow Switch, Previous Part #s: E0013000, E0013100, RE0013100
|
|
|
|
|
|
|
|
|
|
|
|
|
TELEDYNE LAARS RE2075100 Low Water Cut Off, Manual Reset, Rheos and Rheos+, 1200, 1600, 2000, 2400
|
TELEDYNE LAARS RE2077700 EM2 Relay Kit
|
LAARS E2103400 Electronic Temperature Reset Module
|
|
|
|
|
|
|
|
|
|
|
|
|
LAARS R20150201 Machined Bronze Inlet/Outlet Header Cover for Heat Exchanger
|
LAARS R20255400 Machined Bronze Flange 1.5"
|
LAARS R20255401 Machined Bronze Flange 2"
|
|
|
|
|
|
|
|
|
|
|
|
|
LAARS R10391304 Machined Bronze Flange 2.5"
|
LAARS 20266409 Round Venturi Assembly, Natural, 400
|
LAARS 20158602 Square Venturi Assembly, LP, 400
|
|
|
|
|
|
|
|
|
|
|
|
|
LAARS RE0161400 Venturi Differential Pressure Switch, all
|
LAARS 20270402 Ducted Combustion Air Assembly with Round Venturi, 400
|
LAARS 20258102 Ducted Combustion Air Assembly with Square Venturi, 400
|
|
|
|
|
|
|
|
|
|
|
|
|
Teledyne Laars Flue Collector Assembly, 400
|
Teledyne Laars Gas Train Assembly, 320, Natural/LP
|
Teledyne Laars 20268402 Burner Insulation Assembly, 400
|
|