|
|
|
|
|
|
|
|
|
|
|
LAARS 2400-556 Flow Sensor
|
Teledyne Laars 2400-106 Pressure Switch
Used on the following models: CB-M2-150 thru 250 N or L, HW-M2-100L, HW-M2-100N, HW-M2-130N, HW-M2-130LP, cb-m2-200w
|
Laars 2400-097 Pressure Relief Valve, 125 PSI, SMB, Summit
|
|
|
|
|
|
|
|
|
|
|
|
|
Laars 2400-134 Gas Valve, Summit
|
Laars 10-330 Ignitor, Hot Surface, w/Gasket
|
Laars 2400-131 Venturi with Gaskets, Summit
|
|
|
|
|
|
|
|
|
|
|
|
|
AUTO RESET LIMIT 60T11-313154
|
Pilot Assembly Kit Natural Gas
|
Pilot Assembly Kit LP
|
|
|
|
|
|
|
|
|
|
|
|
|
Pilot Assembly Kit Natural
|
Pilot Assembly Kit LP
|
Pressure Switch
|
|
|
|
|
|
|
|
|
|
|
|
|
BLOCKED VENT SWT 150D 36TX16
|
VENTER MOTOR KIT 460V
|
Pressure Switch Natural or LP Gas
|
|
|
|
|
|
|
|
|
|
|
|
|
Pressure Switch Natural Gas or LP Gas
|
FAN CONTROL REPLACEMENT KIT
|
TS121 MT2-12 DUCT SENSOR
|
|
|
|
|
|
|
|
|
|
|
|
|
Reznor 050417 Control Limit-125 6/T11 201234
|
Pilot Assembly LP
|
THERMOCOUPLE #TC2-24 JADE
|
|
|
|
|
|
|
|
|
|
|
|
|
Reznor 201234 Control Limit-125 6/T11 A1248
|
Reznor 110863 Pilot Assy Kit, Match Lit
|
LAARS 2400-135 Burner
|
|
|
|
|
|
|
|
|
|
|
|
|
LAARS 2400-138 Ignitor
|
LAARS 2400-139 Control Board
|
LAARS 2400-151 Field Service Kit
|
|
|
|
|
|
|
|
|
|
|
|
|
LAARS 2400-386 Pump
|
LAARS 2400-388 Bronze Pump
|
Teledyne Laars 2400-574 Pressure Gauge (0-75 psi)
|
|
|
|
|
|
|
|
|
|
|
|
|
LAARS 2400-055 High Limit Saftey
|
LAARS 2400-133 Blower
|
LAARS 2400-136 Combustion Coil
|
|
|
|
|
|
|
|
|
|
|
|
|
LAARS 1302400574 Tube Assembly
|
Teledyne Laars 2400-402 Exhaust Manifold Assy
|
LAARS 2400-137 Gasket Kit
|
|
|
|
|
|
|
|
|
|
|
|
|
Reznor 65986 Burner Rack, RX400 409 A/S L
|
Reznor 112922 SOL VLV H91MG-6D 1 X 1
|
Reznor 085218 BURNER ASSY ALMZ. N. S.
|
|
|
|
|
|
|
|
|
|
|
|
|
Reznor 087954 BURNER ASSY N.S. 409
|
Reznor 088242 H91LG-8 SOL VLV 3/4
|
Laars 10-332 Ignitor Gasket, CB/HWG
The igniter is a “glow bar” type silicon carbide unit. It is energized whenever there is a call for heat and the red "IGNITER" light on the boiler control is lit. After the igniter is switched off and the boiler continues to run, the igniter functions as a flame sensor for the boiler control. If the ignitor fails and must be replaced, always install a new igniter gasket with the replacement igniter. CAUTION: Ignitor gets hot.
|
|
|
|
|
|
|
|
|
|
|
|
|
Teledyne Laars E2078100 Wire Harness, Summit Blower
|
LAARS-2400-058 Thermo cut out
|
Teledyne Laars S2101300 Gaskets and Screws, Venturi
|
|